Best Chainsaw Gloves for Vibration Reduction (2026)

Compare the picks

Specifications are manufacturer rated, collected 19 October 2026. None of these listings states a concrete warranty term.

How we scored them

Each glove is scored out of 10 on performance, build, value, safety and warranty, using only what the listing publishes. Performance here means the stated vibration-dampening features; safety means stated protective features and certifications. The weights are on our How We Pick page.

Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.

Buying guide: best chainsaw gloves for vibration reduction

Padding types: foam, SBR and chloroprene

Four of the five list foam as the dampening method. The Ironclad uses foam padding in impact-resistant nylon that the listing calls vibration-absorbing foam. The JUMPHIGH puts foam inside a pigskin leather palm patch that the listing says absorbs and dissipates vibration, backed by 3D-structured TPR patches on the back running to the fingertips. The HANDLANDY 5805 is foam padded at a stated 0.12 in thickness. The HANDLANDY 635 goes thicker: 5mm of SBR padding on the full palm and fingers, which the listing says absorbs vibration well. The Ergodyne takes a different route with a chloroprene rubber palm pad, and it is the only one with a stated anti-vibration certification, ANSI S2.73/ISO 10819. No listing claims to eliminate vibration; padding dampens it.

Fit: measure the hand first

Three listings publish hand charts. Ironclad lists hand width from 2.1 in at XXS up to 4.8 to 5.2 in at 3XL; this listing is size Large. JUMPHIGH lists hand circumference of 7 to 7.6 in at S and 8.8 to 9.2 in at XL; this listing is Medium. Ergodyne lists circumference from 0 to 7 in at XS/6 up to 12 to 13 in at 3XL/12; this listing is Large. The two HANDLANDY gloves give no chart: the 5805 is Large and the 635 is X-Large. Four close with hook and loop; the Ergodyne is pull-on with an elastic cuff. A glove that swims on the hand dampens nothing well, so match the chart before ordering.

Wash care and water

The HANDLANDY 635 and the Ergodyne list machine wash care; the Ironclad, JUMPHIGH and 5805 list hand wash only. Every one of the five lists a water resistance level of Not Water Resistant, so none is a wet-weather glove. Note the Ergodyne contradiction: its spec table also says Is Waterproof True, which does not square with Not Water Resistant in the same table. Treat the water claim as unclear and keep them dry.

Touchscreens and extras

The Ironclad lists touchscreen as a special feature, the JUMPHIGH makes the thumb and index fingertips touchscreen capable, and the 5805 marks touchscreen with a check. The 5805 adds a TPR wrist guard, a reinforced thumb and a cut-resistant check, plus hi-vis yellow-orange coloring. The 635 lists a reinforced thumb and high-stretch fabric. Extras do not dampen vibration, but they decide whether the glove gets worn all day.

Around the Woodpile

• Wash them the way the listing says: machine wash for the HANDLANDY 635 and the Ergodyne, hand wash for the other three.
• All five list Not Water Resistant, so they are fair-weather gloves; do not count on them in rain or wet snow.
• Size from the charts, not from habit: Ironclad publishes hand width from 2.1 in to 5.2 in across sizes, and Ergodyne publishes circumference up to 13 in at 3XL.
• Touchscreen fingertips on the Ironclad, JUMPHIGH and 5805 mean the phone stays usable without pulling a glove off at the woodpile.

Buying advice: charts, weight and fine print

Three of the five listings publish hand charts, and they do not measure the same thing. Ergodyne gives hand circumference from 0 to 7 in at XS/6 up to 12 to 13 in at 3XL/12; this listing is Large. Ironclad charts hand width instead, from 2.1 in at XXS up to 4.8 to 5.2 in at 3XL; this listing is Large. JUMPHIGH charts circumference at 7 to 7.6 in at S and 8.8 to 9.2 in at XL; this listing is Medium. The two HANDLANDY gloves publish no chart at all: the 5805 is Large and the 635 is X-Large, so buy them only if those sizes fit.

Weight and bulk matter on a long cutting day. The listings state 5.6 ounces for the Ergodyne, 120 g for the HANDLANDY 635, 130 g for the Ironclad and 0.12 kg for the HANDLANDY 5805. The fabric weight classes line up: the Ergodyne and Ironclad are classed lightweight, the 5805 medium weight, and the 635 and JUMPHIGH heavyweight. Four of the five close with hook and loop; the Ergodyne is pull-on with an elastic cuff, and both the Ironclad and the Ergodyne are unlined.

Read the warranty rows before counting on them. None of the five states a concrete warranty term: the Ironclad description warrants against defects with no period stated, the HANDLANDY descriptions cut off mid-sentence at “within 90” with no complete term, and the Ergodyne description is similarly truncated. Also note what the listings recommend the gloves for: impact protection, work, construction and demolition appear, but none of the five names chainsaw use specifically, so the vibration-dampening fit is judged from the padding specs alone.

Frequently Asked Questions

Do anti-vibration gloves stop vibration completely?

No listing here claims that. The listings claim padding that absorbs, dissipates or dampens vibration; treat those as the makers’ claims and expect less buzz, not none.

What is the difference between foam, SBR and chloroprene pads?

Foam is the common method, listed by four of the five. The HANDLANDY 635 uses 5mm SBR padding on the full palm and fingers, the thickest stated pad here. The Ergodyne uses a chloroprene rubber palm pad and carries an ANSI S2.73/ISO 10819 anti-vibration certification, the only stated certification in the group.

Are any of these waterproof?

All five list a water resistance level of Not Water Resistant. The Ergodyne spec table also says Is Waterproof True, which contradicts its own Not Water Resistant row; treat its water claim as unclear.

Which gloves can I machine wash?

The HANDLANDY 635 and the Ergodyne ProFlex 9000 list machine wash care. The Ironclad, JUMPHIGH and HANDLANDY 5805 list hand wash only.

How do I choose a size?

Measure the hand and match the listing’s chart. Ironclad, JUMPHIGH and Ergodyne publish hand width or circumference ranges by size; the two HANDLANDY listings state only Large and X-Large with no chart.

Related guides

See the chainsaw gear hub and chainsaws, plus our chainsaw gloves and chainsaw chaps guides for the rest of the kit.